|
Embossed Votive Holder Shade |
|
|
|
| Articles Art + Drawing Beadwork Candlemaking Crafts for Kids Decoration Dried Flowers Fashion Flower Arranging Framing Jewelry Make Money With Crafts Origami Painting Papercrafts Photography Pottery + Ceramics Puppets + Puppetry Quilts + Quilting Scrapbooking Seasonal Sewing Soap Making Woodworking Wreathmaking |
Embossed Votive Holder Shadeby Michelle GauthierCreate the look of a Stained Glass Votive Holder Supplies Needed: Most items can be found in the Scrap booking/Stamping section of your local craft store. Straight-Sided Clear Glass Votive Holder Vellum Craft Markers of various colors Hole Punch Decorative String Embossing Powder in your choice of color Versamark Ink Pad Embossing Heat Tool Scissors Tape Measure or Ruler 1. Measure the height and circumference of your Glass votive holder with a tape measure or ruler. Use these measurements to cut out a piece of vellum. It is important to make sure that the vellum does not extend past the top of the votive holder because this will increase the risk of a fire hazard. 2. After you have planned your design with your stamp(s), use the Versamark ink to stamp the design onto the vellum. At this point the design will be clear. 3. Now sprinkle the embossing powder onto the stamped design. Turn the vellum upright and make sure all stray powder has been shaken or tapped off. Also make sure that your entire design has been covered in powder. You will be able to see this because the embossing powder will stick to the design that you stamped with the Versamark inkpad. 4. Use your Embossing Heat Tool to heat the powder. But be careful because the heat tool can get VERY hot! You will now have a beautiful raised design of the stamp you chose! Let cool for 1-2 minutes. 5. Now you can just color inside of the design on the opposite side of the vellum. Darker Colors look better for this as they give a bolder appearance when the candle is lit. Allow to dry for approximately 5 minutes or the colors may smear. 6. Finally, use your hole punch to make holes in the center of the shortest sides of the vellum. Run your string through these holes and tie around your votive holder! And, VOILE! A One-of-Kind Votive Shade that was fun and inexpensive to make! You can find more candle decorating ideas at www.ExpressiveCandles.com About the Author: This Article was written by Michelle Gauthier of www.ExpressiveCandles.com. Michelle owns and runs Expressive Candles. They offer hand poured scented candles and shaped tarts. Michelle also has written other candle decorating articles, tips and candlescaping articles. Some craft projects on this site may be unsuitable for children. In any case, adult-supervision is required all children's craft activities and projects. This article is reprinted here with the author's express permission. 
Other websites that may be of interest:
 |
| All views, opinions and ideas expressed in this article are those of the article's author and not necessarily those of Answers 2000 Limited. Privacy Terms Of Use Advertising/Endorsements Disclosures Copyright © 2005-2009, Answers 2000 Limited CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON SERVICES LLC. THIS CONTENT IS PROVIDED 'AS IS' AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME. |
|
|
In Association With Amazon.com
All trademarks are property of their respective owners. All third party content and adverts are copyright of their respective owners. Disclosure: Our company's websites' content (including this website's content) includes advertisements for our own company's websites, products, and services, and for other organization's websites, products, and services. In the case of links to other organization's websites, our company may receive a payment, (1) if you purchase products or services, or (2) if you sign-up for third party offers, after following links from this website. Unless specifically otherwise stated, information about other organization's products and services, is based on information provided by that organization, the product/service vendor, and/or publicly available information - and should not be taken to mean that we have used the product/service in question. Additionally, our company's websites contain some adverts which we are paid to display, but whose content is not selected by us, such as Google AdSense ads. For more detailed information, please see Advertising/Endorsements Disclosures Some graphics on our web sites are Copyright (C) 1997-2000 Hemera Technologies Inc., and used under license. All such pictures are provided for viewing purposes only and are not to be saved or downloaded. All such pictures of recognizable individuals are models and used for illustrative purposes only, and not meant to imply any association or endorsement of said individual with any product or service. |